Phone # 1- 800-678-3313    Fax: 1-616-241-1506     Store & Phone Hours: M-F, 8 - 4:30 EST                                                                        Established 1969

 

 

 

  Home  |  Products  |  Services  |  Custom Tooling  Customer Service  |  Help & Info  |  About Us
- Back
- Crosscutting Blades
- Mitre & Chop Blades
- Ripping Blades
- Strob Saw Blades
- General Purpose
- Laminate Blades
- Plastics Blades
- Non-Ferrous Blades
- Specialty Blades
- Dado Sets
- Panel Saw Main
- Panel Saw Scoring
- Edge Banding Blades

We Accept:

  

Mitre & Chop Saw Blades

 

Freud® LU91 Industrial Thin Kerf Sliding Compound Miter Blades


FS Tool LM6 Mitre Joint Saw Blades

FS Tool L4D Double Cut Off Saw Blades

 

LU91 Industrial Thin Kerf Sliding Compound Miter Blades

Freud Industrial Saw Blades.
 

This thin kerf industrial blade provides a superior finish cut with sliding compound miter saws. The 5° negative hook angle helps prevent the blade from being too aggressive and pushes the work piece down and towards the fence. Thin kerf blades remove less material than standard carbide blades, thus requiring less horsepower to produce equally good results.

 

            I.C.E. Perma-Shield
Ř Teeth Kerf Plate Bore Hook Part # Part #
10" 60 ATB 0.090 0.071 5/8" -5° LU91M010 LU91R010
12" 72 ATB 0.090 0.071 1" -5° LU91M012 LU91R012
 

LM6 Mitre Joint Saw Blades

FS Tool Industrial Saw Blades.

D E S I G N :
  • Tooth configuration: 4 ATB & 1 raker
  • Cutting material: TC
  • Expansion slots: Cu plugged


A P P L I C AT I O N :

  • For mitre joint cuts in soft and hardwoods, painted mouldings, gesso and other high-gloss and pre-finished picture frames and furniture mouldings as well as P.V.C. substrates
  • For aluminum cuts see L1A, L1B, L1C series
  • On single or double cut-off mitre machines and radial arm saws
            Standard
Ř Teeth Kerf Plate Bore Hook Part #
8" 60 0.112 0.087 5/8" 0° to 15°Neg LM6200
8-1/2" 24 0.110 0.071 5/8" 0° to 15°Neg LM4216 [a]
8-1/2" 48 0.110 0.071 5/8" 0° to 15°Neg LM6216 [a]
9" 60 0.112 0.087 5/8" 0° to 15°Neg LM4225
9" 72 0.112 0.087 5/8" 0° to 15°Neg LM6225 *
10" 60 0.116 0.087 5/8" 0° to 15°Neg LM4250
10" 80 0.112 0.087 5/8" 0° to 15°Neg LM6250
12" 80 0.122 0.095 1" 0° to 15°Neg LM4300
12" 80 0.122 0.110 5/8" 0° to 15°Neg LM4308 [b]
12" 100 0.120 0.095 1" 0° to 15°Neg LM6300
12" 100 0.134 0.110 5/8" 0° to 15°Neg LM6308 [b]
330mm 100 3.3mm 2.5mm 20mm 0° to 15°Neg LM6330 [c]
350mm 100 3.1mm 2.5mm 25mm 0° to 15°Neg LM6351 [d]
14" 100 0.142 0.118 1" 0° to 15°Neg LM6350
355mm 100 3.6mm 3.0mm 32mm 0° to 15°Neg LM6350-32 [g]
350mm 108 3.2mm 2.6mm 32mm 0° to 15°Neg LM6353 [e]
14" 100 0.150 0.118 5/8" 0° to 15°Neg LM6358 [b]
15" 100 0.120 0.098 1" 0° to 15°Neg LM6380 [f]
[a] Elu, Hitachi
[b] Pistorious, CTD
[c] Wegoma, Haffner, Salvarani
[d] Makita (with 25mm arbor)
[e] Brevetti
[f] Hitachi
[g] Brevetti (355mm Diameter)
* Grind: 8 ATB & 1 Raker
 

L4D Double Cut Off Saw Blades

FS Tool Industrial Saw Blades.

D E S I G N :
  • Tooth configuration: 3 bevelled one side & 1 bevelled opposite side.
    Supplied in pairs 1 LH & 1 RH (order separately)
  • Cutting material: TC
  • Extra heavy plate provides added stability
  • Expansion slots: Cu plugged


A P P L I C AT I O N :

  • For fine cut-off and mitre cuts of soft and hardwoods, and trimming of
    plywood, wood veneered and plastic laminated panels (single sided), or
    (double sided) using a pre-scoring unit
  • On double cut-off machines and single or double end tenoners
            Standard
Ř Teeth Kerf Plate Bore Hook Part #
12" 80 0.160 0.118 1" 5° to 10° L4D300-LH
12" 80 0.160 0.118 1" 5° to 10° L4D300-RH
14" 80 0.180 0.134 1" 5° to 10° L4D350-LH
14" 80 0.180 0.134 1" 5° to 10° L4D350-RH
14" 100 0.180 0.134 1" 5° to 10° L6D350-LH
14" 100 0.180 0.134 1" 5° to 10° L6D350-RH
16" 100 0.180 0.134 1" 5° to 10° L6D400-LH
16" 100 0.180 0.134 1" 5° to 10° L6D400-RH
 

Click to find out more.

 

© 2008 Carbide Specialties Incorporated

Report problems or suggestions to our Webmaster.

Mitre & Chop Saw Blades